Features:

ü      The chamber, water chamber & outlet are single piece to avoid joints for leakage of water & spreading of powder.

ü      Heavy-duty channel stand & anti vibrating basements.

ü      Four numbers beaters are from special steel & single piece (without joints) are hardened & balanced are sledding to pirated overload. 

ü      Effective and Continuous Grinding

ü      Suitable for Wet-Pulpy and Dry Grinding

ü      Rotating parts are balanced for reducing friction losses & noise. 

ü      Dust free operation. No wastage of product and no pollution hazards.

ü      The Mini Pulveriser grinds almost all Spices, green chilies, fresh ginger, garlic, salt, sugar, coffee, fresh fruits, fruit pulp, vegetables, tobacco, herbs, beetle nuts, herbs, roots, leaves, bark of trees, oil cake, cattle and poultry feeds, icing sugar, costarred powder, instant food, food colors and allied food production.

        Specifications:

Model	TW-4 SUPER	TW-5 SUPER	TW-6 SUPER
DIA X WIDTH IN INCH	8 X 4	10 X 4	12 X 4
Motor (HP)	2 To 3	5 To 7.5	7.5 To 10
Grinding Speed (RPM)	4,500	5,000	5,000

AlterNet

• All contacting parts of stainless steel 304 / 316 can be supplied at extra cost. Please ask for the prices.

   

• Oil chamber for lubricating of the bearing instead of grease chamber at extra cost

   

• Cutting the wheat & rice into pieces recommended running at low speed (650 R.P.M.) and using suitable screens.

   

Standard Accessories:

·                     A set of 6 Nos. perforated round hole screens are supplied with the machine.

·                     Water tank, motorized coolant pump, pipes & pipes Fittings.

·                     Cotton balloon.

·                     The fabricated stand & mild steel basement are made from “C” channels wheel & with rails.

·                     2 X "B" sections V Grooves pulley for Machine & motor.

·                     Stainless steel hopper.

Operation:
                full the water tank with water. The flow of material from the Feeding Hopper is regulated by means of a Vertical Adjustable Slide to suit the load indicated by the ammeter. Rotor with four beaters runs in anti-clockwise direction. The swinging beaters pass just beneath the Ratchet Teeth Liner fitted inside the top half of the grinding chamber, leaving a gap of 1/8" between the liner teeth and the tips of the rotating beaters. This cuts the material caught between the liner teeth like a sword with a scissors action at a high speed of 4500/5000 rotations per minute.

After the required size reduction, the material will pass through the screen fitted inside the lower discharge end of the grinding chamber. No sieving is required, as the appropriate size screen fitted will not allow coarser material to pass through. The air generated in the grinding chamber forces the powder to pass through the screen fitted at the bottom discharge end of the grinding chamber, into a cotton bag attached to the delivery trough below. The dust is collected through the attached balloon fitted on the discharge end. The top closed end of the balloon may be suspended from the roof or a wall of the building. Every half an hour, the balloon should be tapped to knock down the dust clogging the pores of the balloon, thus releasing the pressure built-up. The dust falls in the bag below, and thus a dust free operation without wastage of product can be achieved. (When crushing Wet-Pulpy materials, the balloon should not be used)

Servicing Guidelines:

Open the cover of chamber all grinding parts can be cleaned with a brush in couple of minute and the pulverizer is ready for next grinding. If required, the grinding chamber can also be washed with water. Remove the cotton balloon and the screen, close the cover tightly and start the grinder. Now pour a bucket or two of water into the hopper. The grinding parts will be flushed with the water and cleaned. Continue running the machine for a few more minutes as the draft of the fresh air sucked into the grinder will dry it. The beater when worn out can be removed and reserved by removing the cur clip lock holding to the rotor pins. When both the edges are worn out, they can be sharpened on an emery stone, to be used as new. In addition, when completely warn out, can be replaced the equal weight and refitted.